Holybro Kakute H7 V1.3 FC & Tekko32 F4 4in1 ESC STACK

  1. MCU: STM32H743 32-bit processor running at 480 MHz
  2. IMU: MPU6000
  3. Barometer: BMP280
  4. OSD: AT7456E
  5. Onboard Bluetooth chip: ESP32-C3

 

 100.10

Out of stock

Out of stock

16 People watching this product now!

Holybro Kakute H7 FC Manual

DOWNLOAD

MCU

STM32H743 32-bit processor running at 480 MHz

IMU

MPU6000

Barometer

BMP280

OSD

AT7456E

Onboard Bluetooth chip

ESP32-C3

Battery input voltage

7V to 42V

Mounting

30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets

Dimension

35x35mm

Weight

8g

Shipping Weight 0.07 kg
Shipping Dimensions 10 × 7 × 4 cm

This is Holybro Kakute H7 V1.3 FC & Tekko32 F4 4in1 ESC STACK.

The Holybro Kakute H7 V1.3 Flight Controller is full of features including integrated Bluetooth, dual plug-and-play 4in1 ESC ports, HD camera plug, barometer, OSD, 6x UARTs, full Blackbox MicroSD card slot, 5V and 9V BEC, easy soldering layout and much more.

The Kakute H7 builds upon the best features of its F7 predecessor and further improves on hardware components and layout. With the additional integrated Bluetooth chip onboard, you can perform Betaflight configuration and tune wirelessly on your phone with the SpeedyBee Android & IOS App. The Kakute H7 is DJI HD ready. It has an easy plug-and-play port with an onboard 9V regulator designed to power your HD video transmitter like DJI/Caddx FPV Air Unit & Caddx Vista while supporting an analog system.

It has 6x dedicated UART ports with built-in inversion for peripherals (UART2 is used for Bluetooth telemetry), along with a full MicroSD Card slot for virtually unlimited Blackbox data logging. Dual plug-and-play 4in1 ESC connectors, allowing easy plug-and-play support for x8 Octocopter configuration and keeping it simple and clean. The integrated BetaFlight OSD makes it easy to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features, and more. It is also ready for autonomous flight with the on-board barometer. There are LED & buzzer pads, and I2C pads (SDA & SCL) for external GPS/Magnetometers.

Note: Atlatl HV V2 is not included.


Features:

  1. New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
  2. PWM Frequency: 16k to 96k
  3. A separate drive & control circuit broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

ESC’s Specification:

  1. Continuous Current: 50A x4
  2. Burst Current: 60A x4
  3. Supports 4-6S battery
  4. Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
  5. ESC telemetry Supported
  6. Onboard analog current sensor
  7. No output BEC
  8. BLHeli_32 firmware
  9. 1000uf 35v capacitor included (highly recommended for 6s setup)
  10. Amperage meter scale ratio: 168
  11. Dimensions: 45x37x6mm / Weight: 13.8g
  12. Mounting holes: M4 30.5×30.5mm (M3 grommets included)

Package Includes:

1 x  Kakute H7 v1.3 STACK (FC+ESC)

1 x  Electrolytic capacitor: 1000uF 35v

1 x  8pin to 8pin 1mm pitch 65mm cable

1 x  8pin to 8pin 1mm pitch 25mm cable

1 x  JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)

1 x  JST SH 6pin 100mm cable(for Caddx HD Systems)

 

0 reviews
0
0
0
0
0

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.